方式1:
按下把持板上的FUNC键，此时RUN灯开端闪亮，按住此键超越8秒，RUN灯变为常亮，此时顺序进入开关门行程跟过载力进修进程；
方式2:
按INC键，此时电机开端向开门的偏向运行，按住不放，电机运行速率由慢转快，同时RUN唆使灯闪亮，标明电机向上运行。达到幻想的地位后松开按键，电机结束运行；假如按下DEC键，则电机由慢转快向关门偏向运行，STA灯闪亮。用这两个按键可调理上到位的地位。
方式3:
假如上到位的地位调剂适合后，按FUNC键一次，则RUN唆使灯疾速闪耀后燃烧，标明上到位进修实现；同时STA唆使灯点亮，顺序进入下到位进修进程；
方式4:
用 INC跟DEC两个按键调剂下到位地位，在达到预约地位后，按FUNC键一次，此时STA灯闪亮，标明下到位进修实现；
方式5:
高低到位地位进修结束，顺序主动进入开关门力气进修：门体首先向开门的偏向运行，同时RUN灯点亮，在门体运行的进程中，顺序主动丈量运行中门体所遭到的阻力，达到上到位后，主动结束，延时一段时光后，顺序主动关门，此时STA灯点亮，顺序丈量关门时的力气，达到下到位后，主动结束；
方式6:
力气进修结束，保留全部进修到的值，同时RUN、STA灯闪亮数次，标明顺序进修结束；
方式7:
此时按遥控器上的按键或墙壁开打开的按键，则电机依照请求运行。
留神事项
1、对非尺度车库门，请你务必收罗制作厂商的看法；
2、操纵遥控器或墙壁按钮前必需确保门体均衡体系任务状况精良；
3、全部供给的警示标签应贴在明显的处所；

Method 1:

Press the FUNC key on the control board, then the RUN light will start to shine. Hold down this key for more than 8 seconds, and the RUN light will turn on normally.

Method 2:

Press the INC key, then the motor starts to RUN in the direction of opening the door. Hold it down and the motor speed will turn from slow to fast. At the same time, the RUN light will flash, indicating the motor runs upward. After reaching the fantasy status, release the button and the motor will end operation; If press the DEC key, the motor will turn from slow to fast to close the door, and the STA light will shine. Use these two keys to adjust the position in place.

Method 3:

If the position in place is suitable for adjustment, press the key of FUNC once, then RUN ablates the lamp to burn after flashing rapidly, indicating the realization of advanced study in place; At the same time, STA abetted the light to turn on, and then entered the process of further study in place.

Method 4:

Use the two keys of INC and DEC to adjust the lower position. After reaching the reservation position, press the FUNC key once. At this time, the STA light will flash, indicating the lower position for further study.

Method 5:

Status in study of on any account, order the initiative into the open close strength training: door to open the door of the first to RUN, RUN the lamp lit at the same time, the door in the process of operation, the order of active measurement encountered in the operation of the hydrodynamic drag, after reaching on in place, take the initiative to end, after a time delay, order closed, at this time the STA lights up, order measure close strength, after reaching down in place, take the initiative to end;

Methods 6:

At the end of the training, keep all the values of the training, at the same time, RUN and STA lights flash several times, indicating the end of the training sequence;

7:

At this point, press the button on the remote control or the button to open or open the wall, and the motor will run according to the request.

Be careful considerations

1, for non-standard garage door, please be sure to collect the views of the manufacturer;

2. Before operating the remote control or the wall button, it is necessary to ensure that the door body balance system is in good condition;

3. All supplied warning labels shall be posted on conspicuous places;